Thread Rating:
  • 6 Vote(s) - 2.67 Average
  • 1
  • 2
  • 3
  • 4
  • 5
rear shocks, boy did I mess up
I removed the rear shocks to replace the rubber boot on the shock from the bike before I bleed the air off and blew oil all over. :oops: :roll:

Now how do I know how much oil I need to have in it?

How do I make sure the old oil is all gone?

Where can I find a rubber boot to replace the one on there now?

I guess I don't need to rebuild the shock cause it was holding air or should I rebuild it now that I am in this fix?

I feel like a novice on this one? :ymblushing:
US Navy (Ret) Submariner

USS Bergall, USS Archerfish, USS GC Marshal (B),
USS US Grant (G), USS Skipjack, USS Swordfish,
USS Alabama (B)

Spent a day or two underwater.....
Reply
#1 01-11-2011, 11:48 AM,
Sounds like something I would have done. #-O #-O If I were in that spot and could afford it, I'd go ahead and replace with Progressive shocks. If not, just hang on a bit and one of the resident experts will have a very accurate answer for you. :d :d
Reply
#2 01-11-2011, 12:02 PM,
in a pinch it is possible to refill the shocks thru the air ports but its a slow process,if you were replacing the seals the req is approx 10.5 oz of atf,safe amount would be 9oz if your doing it thru the ports,your present atf probably is not really atf now

you can turn the shocks upside down and drain them but it takes about a day to drain them completely,the shock bellows are available thru any honda dealer on special order but below are several links where prices are discounted

<!-- m --><a class="postlink" href="http://www.westernhonda.com/fiche_section_detail.asp?section=146200&category=MOTORCYCLES&make=HONDA&year=1984&fveh=3442">http://www.westernhonda.com/fiche_secti ... &fveh=3442</a><!-- m --> you'll probably need # 12 and 15 minimum,if you want to use new seals,#24 is what you'll need

<!-- m --><a class="postlink" href="http://www.cheapcycleparts.com/model_years/268-honda-1984-gold-wing-aspencade-GL1200A/assemblies/5273">http://www.cheapcycleparts.com/model_ye ... blies/5273</a><!-- m -->

<!-- m --><a class="postlink" href="http://www.hondapartspitstop.com/pages/parts/viewbybrand/7/Honda.aspx">http://www.hondapartspitstop.com/pages/ ... Honda.aspx</a><!-- m -->

<!-- m --><a class="postlink" href="http://www.hdlparts.com/fiche_section_detail.asp?section=146200&category=MOTORCYCLES&make=HONDA&year=1984&fveh=3442">http://www.hdlparts.com/fiche_section_d ... &fveh=3442</a><!-- m -->

all the above dealers are pretty much close on price,only difference seems some charge a little more than others on s/h,but i've ordered from all of them with good results,there may be others close to u on the west coast
1987 Aspencade 129K
1986 SEI 93K
2014 Tri-Glide HD 17K

Hancock,MD
Reply
#3 01-11-2011, 12:45 PM,
Earl you're a freakin' encyclopedia of information. Amazing!

But how come you can't make the snow and cold go away?
:d
A rainy day off beats a sunny day at work any time..................
Reply
#4 01-11-2011, 02:18 PM,
john,
its all your fault after it leaves your house you keep sending it down this way,so dont blame me,who lives northwest of you,blame them B-( B-( B-( B-( B-(
1987 Aspencade 129K
1986 SEI 93K
2014 Tri-Glide HD 17K

Hancock,MD
Reply
#5 01-11-2011, 02:21 PM,
Follow this link <!-- m --><a class="postlink" href="http://www.goldwingfacts.com/forums/view_topic.php?id=14189&forum_id=9&highlight=rebuilding+shocks">http://www.goldwingfacts.com/forums/vie ... ing+shocks</a><!-- m --> and it will describe in great detail how to rebuild/refill GL1200 rear shocks.
Ed (Vic) Belanger - 1954-2015
Founder of gl1200goldwings.com

Reply
#6 01-11-2011, 04:44 PM,
waltharper : note if there are any clean spots on the ceiling in your garage then you still have oil in your shocks haha dont feel bad we all have done things like that. We learn by our mistakes and try not to do them again, just think you just taught someone a new ,not what to do good luck with your rebuild Hal
Reply
#7 01-11-2011, 05:50 PM,
Walt, Go to the link posted by Vic. That is how I rebuilt mine, even built the tool in a similar manner. I ordered Progressive springs, factory seals, and refilled with ATF. Do what the Gambler says and you can't miss.

Patrick

Oh, and if you were an A ganger or a nuke, I would't admit it here. (The former ET1(SS))
Reply
#8 01-11-2011, 11:02 PM,
Sorry to hear about the shock explosion. I have a question about progressive air shocks! I have a set that is leaking from the cheap connectors . Is there a better connector/ hose set up for them I can use. The one they sent me with the shocks are plastic and seem very cheap. I have 300+ in air shocks that leak out totally within a couple of days.

Thanks
Ray
Reply
#9 01-12-2011, 02:43 AM,
My left shock is leaking a little at the bottom. Would it be acceptible to replace them with Progressive 14.25" spring ones. Have any of you done this? Thanks.
Bob
Reply
#10 01-12-2011, 10:39 AM,
I tried to view the pics about rebuilding the shocks but was not allowed to do so. Site massage said I must be logged in. I think I am logged in all the time??
Bob
Reply
#11 01-12-2011, 10:44 AM,
Rob, I used the springs Progressive sent me for the bike, matching the part #. In Gambler's post, he does point out that the Progressives are taller. Not to worry, with the custom tool, they install just fine. Actually, next to the timing belts, one of the easiest things I've ever done to my Wing. I removed all the rear tupperware and cleaned many years of mung and drool while I was at it and fabricated a set of extensions for the trunk while I had it removed.

Happy wrenching, Patrick
Reply
#12 01-12-2011, 04:52 PM,
replacing the seals and refilling is easy and simple,even upgrading the springs with the progressive replacements for the stock shocks is not that hard,complete rebuild of the stock shocks with all parts is somewhere less than half of the new progressives

have progressives on one GL and upgrades on another and i really cant tell the difference except in my wallet,wish i'd known about the rebuilds about a year earlier

have two sets here i'm about to refurb soon and put on ebay

and rob,occasionally moving around the site will kick you back to a visitor status,happens to me all the time
1987 Aspencade 129K
1986 SEI 93K
2014 Tri-Glide HD 17K

Hancock,MD
Reply
#13 01-12-2011, 06:28 PM,
i am,but you weren't supposed to tell anybody till after Dec 21st,2012 when my "ship" leaves
1987 Aspencade 129K
1986 SEI 93K
2014 Tri-Glide HD 17K

Hancock,MD
Reply
#14 01-12-2011, 10:20 PM,


Possibly Related Threads…
Thread Author Replies Views Last Post
  Rear Air Shocks goldwingrider 15 2,174 04-18-2015, 12:43 PM
Last Post: lucian
  Progressive rear shocks keystone373 11 1,944 08-10-2013, 03:42 AM
Last Post: wingandaprayer
  Rear shocks ship 4 807 01-29-2013, 10:46 AM
Last Post: ship
  All parts need to rebuild rear shocks. BigDaddy12t 12 2,147 07-06-2012, 02:20 PM
Last Post: Ed Z
  Oil in rear shocks Ofen 9 1,167 04-17-2012, 07:02 AM
Last Post: seabee
  Rear shocks BigDaddy12t 9 1,138 04-06-2012, 04:45 AM
Last Post: admin
  Rear Shocks Bottoming Out JackH 14 1,552 02-02-2012, 06:27 AM
Last Post: wingandaprayer
  Inside the Rear Shocks delvis 11 1,692 01-14-2012, 10:23 PM
Last Post: 85GL1200I
  Good non-air rear shocks (progressive) RCB 11 1,458 09-29-2011, 08:08 AM
Last Post: RODNUT
  Progressive springs for rear shocks 10 1,599 10-02-2010, 03:10 PM
Last Post: BladeRunner

Forum Jump:


Users browsing this thread: 1 Guest(s)

Contact Us | GL1200 GOLDWINGS | Return to Top | | Lite (Archive) Mode | RSS Syndication
google-site-verification: googled4b4fe31e07b65d8.html