Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Your links to parts sources are valuable and needed.
Hello all , I am looking for parts to restore my GL1200 Standard. I am actually pretty much well on my way and need very little to complete it , one of the parts needed is the landing cover for the right-hand side in front of the false tank that hides the frame and the radiator filler cap that's underneath it . It is about 7"X3" black plastic and slips under the false tank top of the frame . I'm sure everybody with the standard most part I'm talking about . I know this is a difficult part to find and I'm going to pay up for . I was wondering if someone that has one might know someone with a 3D printer that could make one , again I'm going to pay up . Please let me know and thank you . Eric
Reply
#31 09-02-2016, 10:34 PM,
Show me the part on here

http://www.sturgessonline.com/fiche_sele...veh=132497

I'm going to presume you have tried Ebay
The only stupid questions are the one's that are not asked.

Reply
#32 09-03-2016, 09:58 AM,
(09-03-2016, 09:58 AM)SIR tricky Wrote: Show me the part on here

http://www.sturgessonline.com/fiche_sele...veh=132497

I'm going to presume you have tried Ebay
Tricky,

I think the part he is looking for is #24 in the diagram. CVR R FR Shelter Part # 83141-MG9-000. I might have one, but I'll have to look for it.

Poorboy
Reply
#33 09-03-2016, 04:21 PM,
I need to rebuild the front forks and rear air-shocks on my 85 aspy. Is there a "list " of parts to replace and or inspect during the rebuild. Also where can I acquire said parts. All help and info Very much appreciated
Reply
#34 03-21-2017, 10:52 AM,
I wonder if you can get anything from this

http://s145.photobucket.com/user/trickeo...sort=3&o=9

You should be able to get parts from your local Honda dealer (hopefully)

The link is to parts of the 84-85 manual for the goldwing.

I find it easier to remover the forks from the bike and do things on the bench., You will need a soft jaw vice or lots of cloths around the forks.

Make sure you undo the bottom allen bolts before removing the top cap, be aware the cap is under pressure when removing it.

I usually use a ratchet and socket and keep my chest pressing down as I remove the cap.

I would replace the springs with progressive springs makes for better handling, I know they are expensive but I replaced my rear shocks with progressive units. http://www.progressivesuspension.com/
The only stupid questions are the one's that are not asked.

Reply
#35 03-21-2017, 05:24 PM,
More sources;

http://cyclemax.com/ Valley City, Ohio could be in your area.

http://www.hondadirectline.com/
The only stupid questions are the one's that are not asked.

Reply
#36 03-22-2017, 05:49 AM,
Willies cycle salvage in camp hill AL.
Have got metric parts from them quite a bit.

Just ordered a single carb body for a 81gl 1000 from them.
Reply
#37 03-22-2017, 05:18 PM,


Possibly Related Threads…
Thread Author Replies Views Last Post
  PARTS NEEDED 8 791 05-16-2011, 02:03 PM
Last Post: RobH
  Two New Sources Keener 2 408 04-22-2011, 04:59 PM
Last Post: bluewing
  Good Sources 2 859 02-10-2007, 12:15 PM
Last Post: admin

Forum Jump:


Users browsing this thread: 2 Guest(s)

Contact Us | GL1200 GOLDWINGS | Return to Top | | Lite (Archive) Mode | RSS Syndication
google-site-verification: googled4b4fe31e07b65d8.html